|
All siemens
phones:
SP unlock *#0003*(secret code 8
digits)#
Siemens S1 /
S3
Show IMEI code:
* # 06
#
Tetris: Power on
phone and enter PIN. before phone has locked onto network, F9,
send own number, hit right button, hit 9. left is 2, right is 8,
rotate is 5,
and drop is 4.
Monitor Mode:
Menu, 9 (Phone Options), 7 (Phone Status), Left Display Button
(left MENU key), 5553756, HangUp Button (Red HandSet key)
Now "Monitor" should appear at the bottom of the Network Options
menu.
Pressing the right Display Button when in monitor mode
will show a list of the
six cells with the strongest
signals.
Test Mode Indicators: (* = only available when call in
progress )
CH Channel
Number
RX Signal Strength
(dB)
N NCC (Color
Code)
B BCC (Color
Code)
CI Cell ID (in Hex)
C1+
how long before phone does forced hand over. (see RX and
RXAM)
LAI Location Area Identity. Display
Network ID code (42F010 = 240.01)
and
MSC
TXPWR Transmit Power
(dB)
RXAM Reeceive signal strength
cut-off point
TS*
Time Slot
Number
TA* Timing
Advance. Distance from tower in Km X
2
PL* Power
Level
Power Table
PL: 5 6 7 8 9 10 11 12 13 14
15
dB: 33 31 29 27 25 23 21
19 17 15 13
Watts: 2 1.3 .8 .5 .3 .2 .13 .08
.05 .03 .02
LF* C1 value with continuous
transmisson from tower
LS* C1 Value with
discontinuous tranmission from tower
QF* Bit
Error Rate with continuous transmission from
tower
QS* Bit Error Rate with discontinuous
transmission from tower
BER (bit error rate)
table
QF/QS register: 0 1 2 3 4 5 6 7
% of bit
sent: 0.2 0.8 0.4 1.6 3.2 6.4 12.8
25.6
Siemens
S3:comfort
Show IMEI code:
* # 06
#
MONITOR MODE
The Siemens S3 Com
series have a Monitor mode that can be activated directly
from
the standard user keypad. In order to activate this mode, you must
enter
the special access code currently programmed into the
phone.
TO ACTIVATE MONITOR MODE:
Turn the
phone on.
Enter the PIN access code on press OK. (Only if is
enabled).
Press Menu. (Left top button).
Press 9. (Phone
Options).
Press 8. (Phone Status) (May be button 7 in some
phones).
You may see your IMEI Number
Left Display Button
(Top left MENU key).
7684666
HangUp Button. (Red HandSet
key).
Note: Monitor should appear now at the bottom of the
Network Options menu.
MONITOR MODE
TOGGLE
Pressing the right Display Button when in monitor
mode will toggle into 1 and
2 modes
Tips
and tricks:
Nice Sundown in
the display.
Siemens S3 or younger:
In the Telephone Book in
the section own numbers, first position you have to type in
+12022243121 (Number of the Capitol in Washington DC) and save it
without a name. Then open this telephone book again do so as you
like to change the number but leave the modus without changing
anything. A nice Sundown will be shown in the
display.
Siemens S4/S4 Power
Show IMEI code:
* # 06
#
MONITOR MODE
The
Siemens S4 series also haves a Monitor mode that can be activated
directly from
the standard user keypad. In order to activate
this mode, you must enter the
special access code currently
programmed into the phone.
TO ACTIVATE MONITOR
MODE:
Menu, 9 (Phone Options), 7 (Phone Status), Left
Display Button (left MENU key),
7684666, HangUp Button (Red
HandSet key)
Now "Monitor" should appear at the bottom of the
Network Options menu.
Pressing the right Display Button when in
monitor mode will show a list of the
six cells with the
strongest signals.
Test Mode Indicators: (* = only available when
call in progress )
Unlock Siemens S3/S4 (Not
S3 COM)
(For advanced users
only)
At addresses 0D8 to 0DD the
phones code is stored. To read the
code swap nibbles
stored at addresses from 0DA to 0DD. Error
counter is
at 0D9. To clear the Phone Code write at
addresses
from 0D8 to 0DD: 00, 00, FF, FF,
FF, FF.
Siemens C
25
Show IMEI code:
* # 06
#
Resets language to automatic selection :
* # 0000 # then Green
button
Pin Out
Phone's connector
pin-out:
1- GND
2- SB
3- POWER
4- NC
5- TX
6- RX
7- CLOCK
8- DATA
9- GND MIC
10-
HF MIC
11- AUDIO
12- GND AUDIO
|